36v WET (6) 6v / 420ah & 36v / 36a charger
370-024
(Qty: 6) 6-volt / 395ah AGM (Maintenance Free) batteries
370-020 Instead of the standard (Qty: 6) 325ah batteries (WET), a set (Qty: 6) 6-volt / 395ah AGM (Maintenance Free) batteries and special charger is provided. Our experience has been that AGM batteries may not offer as many cycles (recharges) as properly maintained lead acid (WET) batteries. They are suitable for customers who prefer their maintenance free nature, and reduced gassing during recharge.
(Qty: 6) 6-volt / 420ah WET batteries
370-060 Instead of the standard 325ah batteries (WET), a set (Qty: 6) 6-volt / 420ah WET batteries is provided. This option does not require and charger upgrade. These batteries offer approximately 30% more run time than the standard 325ah batteries.
Charger, Universal Voltage-Wet 36v/25a (Dual Pro) up to 325ah
370-081
36v / 40a 220v AC Charger Lester - Console for 420ah
370-082
Charger On-Board SPE Sealed 36v/33amp
370-109 Charger On-Board SPE Sealed 36v/33amp is designed to mount directly to the auto-scrubber and eliminate the need to store a charger remotely. This unit has some protection against water.
Plastic Battery Cover
370-036 Plastic Battery Cover is a simple sheet of plastic that covers the tops of the batteries, offering a 2nd layer of protection for the battery posts. This walk behind scrubber comes standard with individual rubber booties for each battery post, but some customers prefer a supplemental sheet that covers the entire battery, cell caps and all.
Single Point Water System
370-038 Single Point Water System for (Qty 6) 6v/325ah batteries allows easy battery watering, by connecting all of the battery cells via special caps. These caps connect to a single tube for watering of the scrubber”s batteries, and help to equalize the electrolyte levels.
Industrial Battery 440ah & Charger
370-112 Industrial Battery 440ah & Charger Ferro Five Charger 1-Phase equips the rider scrubber with a large capacity ‘steel case— material handling battery, in place of the standard (Qty 6) 6-volt / 325ah individual batteries. The option also includes the appropriate charger for this larger capacity battery, and requires installation by a qualified electrician, since unlike the standard chargers ‘wall plug— for AC, this charger is typically hard wired. The industrial battery adds almost 600 pounds to the weight of the scrubber, and can impact ramp climbing ability. However its benefit is 35% more run time and a battery that when properly cared for has a 5 year warranty.
Industrial Battery 440ah & Charger
370-114 Industrial Battery 440ah & Charger ‘Universal AC / Rapid equips the rider scrubber with a large capacity ‘steel case— material handling battery, in place of the standard (Qty 6) 6-volt / 325ah individual batteries. The option also includes a ‘Rapid Charge— appropriate DC output charger for this larger capacity battery, and requires installation by a qualified electrician, since unlike the standard chargers ‘wall plug— for AC, this charger is typically hard wired. The industrial battery adds almost 600 pounds to the weight of the scrubber, and can impact ramp climbing ability. However its benefit is 35% more run time and a battery that when properly cared for has a 5 year warranty.
Industrial Battery 440ah
370-2110 Industrial Battery 440ah equips the rider scrubber with a large capacity ‘steel case— material handling battery, in place of the standard (Qty 6) 6-volt / 325ah individual batteries. The industrial battery adds almost 600 pounds to the weight of the scrubber, and can impact ramp climbing ability. However its benefit is 35% more run time and a battery that when properly cared for has a 5 year warranty.
Industrial Battery Box without Battery
370-588 Industrial Battery Box without Battery ? Includes Conversion Bracket and Box is a unique option that equips the rider scrubber with the ability to accept the ‘Industrial— battery at some point in the future. The battery floor scrubber will be shipped with standard batteries in the deep plastic tray, held in place by a steel bracket. At a later date, these batteries and bracket could be removed and with room to slide in the 440ah steel case battery. Developed initially for international inventory and necessary flexibility.
Industrial Battery Lift Out Tool
370-035 Industrial Battery Lift Out Tool is a certified device that we sourced, and is properly rated to safely lift out our 440ah (1,300 lb) steel case battery. It is highly recommended, as use of metal chains or nylon straps create hazards with potential injury or death.
Roll Out Battery Box
370-037 Roll Out Battery Box ? Battery Not Included is an option that equips the rider scrubber with a special box for Industrial Battery Roll-Out. The option does not include the battery/charger or the ‘removal— equipment. Designed to be used in collaboration with approved battery exchange equipment.
Single Point Water System for Industrial battery
370-040 Single Point Water System for Industrial battery allows easy battery watering, by connecting all of the battery cells via special caps. These caps connect to a single tube for watering of the scrubber”s batteries, and help to equalize the electrolyte levels
Chemical Free, Oscillating, Strip/Scrub Disk System
370-141 Chemical Free, Oscillating, Strip/Scrub Disk System uses the oscillation of the brush driver, special sanding pads, enhanced scrub motor hp, rpm and pressure to allow the floor scrubber to clean floors or strip wax without using harsh chemicals. The option includes a ‘mode— switch allowing the operator to switch back to traditional settings, making it uniquely able to move from strip mode, back to scrub mode.
ECON- Energy Saver Switch
370-290 ECON- Energy Saver Switch allows the scrubber operator to choose between standard performance range (maximum) or ‘reduced— performance range and thus conserve energy and extend the runtime. Intended to be one of many environmentally conservative measures we”re taking to reduce energy use.
Spray Jet option
370-127 Spray Jet option equips the scrubber with a heavy duty hose 4” - 10” and spray nozzle. This allows the operator to use the scrubber”s clean solution under pressure (3.0 gpm / 45 psi) to flush out the recovery tank when draining the tank when fresh water source is not within reach. Operator can also cleanout the scrub deck/hopper, pre-spray a large floor area for better detergent dwell time, cleaning under racks, around equipment, into restrooms and more.
Vacuum Wand
370-129 Vacuum Wand extends the reach of the scrubber”s vacuum system. The option includes a steel wand and vacuum shoe, and a 12” flexible hose to connect to the recovery tank. It permits the operator to recover spills under racking, behind cabinets or cleaning restroom floors.
Spray Jet / Vac Wand Combo
370-131 Spray Jet / Vac Wand Combo equip the scrubber with both of the previously described options.
On-Board Soap System (SUDS)
On-Board Soap System (SUDS). This Super-concentrated Universal Dispensing System automatically and precisely meters the soap into the solution stream, thus avoiding spills, misuse of chemicals, unauthorized dilution adjustments, etc. By blending the scrubber soap at the end of the solution stream, only fresh water is used to fill the tank, or run through the solution system”s filter and solenoid valve, reducing potential clogs with these items. The SUDS jugs include cap inserts with valves to protect operators from exposure, a big safety feature of traditional drums and pales of soap. The system allows the operator to run with it OFF, Normal or Double Dose. The option includes a box of (Qty: 2) 2.5 gallon jugs of PowerCat detergent to get the customer started.
Tires ? Grey Non-marking Front and Rear
370-177 Tires ? Grey Non-marking tires are in place of the standard black rubber tires. This allows customers to operate on sensitive floors like ceramic tile, glossy epoxy or waxed surfaces with lower risks of potential black marks. WARNING: Grey tires are more susceptible to harsh industrial chemicals, and so are only recommended for use in ‘commercial— applications. Therefore, they come with a limited warranty.
Tire, Drive, 12" Polyurethane
370-184
Tire, Front, 12", P7 - in lieu of black hytraq rubber
370-186
Tires ? P7 Rear Only
370-179 Tires ? P7 Rear Only allows customers to improve the good traction characteristics of a black rubber tire, but without the potential for marking sensitive floors. WARNING: P7 tires are susceptible to flat spots if left parked idle for long periods of time, or cold storage. Therefore, they come with a limited warranty.
Vacuum Muffler Package
370-225 Vacuum Muffler Package XR Series equips the floor scrubber with enhanced sound reduction material and vacuum exhaust routing. The option is popular in applications where every measure of sound reduction is appreciated, like hospitals, casinos or anywhere that minimal decibel readings are required.
Managers” Lock-Out Brush Pressure
370-305 Managers” Lock-Out Brush Pressure allows a Manager, with a private key, to lock out the scrubber”s Scrub pressure adjustment. Our scrubbers offer 5 down pressure settings, and should only be used on maximum settings for floors with heavy soil build up or stripping floor finish. To avoid unnecessary wear on brushes or brushes, this lockout can be employed to maintain Managements” preferred settings.
Manager”s Lock-Out Solution Control
370-310 Manager”s Lock-Out Solution Control permits a Manager, with a private key, to lock out the scrubber”s Solution Flow adjustment. Our floor scrubbers offer 6 settings for solution flow (Off, 0.2 gpm, 0.4 gpm, 0.6 gpm, 0.8 gpm, 1.0 gpm), with Heavy flow only needed for thick soil, dusty applications or times when cleaning at a higher transport speed. To limit the waste of water, the solution setting can be locked.
E-STOP
370-285 E-STOP is a RED kill switch on the dash board, that when depressed cuts off the key switch circuit, disabling all systems on the scrubber. It is intended for use during a panic, when the operator may struggle to locate or operate the key switch.
LED Headlight Upgrade
370-300 LED Headlight Upgrade is a swap out option equipping the scrubber with LED headlight, in place of the standard ones. These LED units offer reduced energy consumption and are significantly brighter. Especially helpful in ‘low light— applications like remote areas of a warehouse or operating in semi trailers, freezers, etc...
Rental Package Central Command
370-330 This is a central command built with old fashioned (1990's) technology. A simple curtis speed controller and all other systems running on switches, relays and circuit breakers. It's designed for use in markets that prefer reliability and ease of service over all of the automation we have with our standard system.
Seat with Switch
370-335 Seat with Switch equips the standard seat with a ‘cut-off— switch. This switch disables the key switch circuit on the scrubber if the operator is not properly seated.
Strobe Light
370-340 Strobe Light ? Amber is a flashing light mounted to the top/rear of the scrubber”s recovery tank. The strobe light increases the floor scrubber”s visibility to other vehicles or people, and is recommended in congested facilities.
Dash Mount Solution Shut Off XR Series
370-352
Battery Disconnect
370-354 Battery Disconnect gives the scrubber operator the ability to disconnect the battery pack leads between the batteries and the controller. Then an external charger can be plugged in for recharging the batteries. It also comes in handy for servicing the scrubber, as disconnecting the batteries is recommended before conducting any machine repairs.
Turn, Brake, Back Up Light Kit
370-358 Turn, Brake, Back Up Light Kit ? Front/Rear with Stalk equips the floor scrubber with lights similar to those found on an automobile. Turn signals to indicate lane or direction changes. Brake lights when the scrubber decelerates. Back Up lights to offer lighting when the scrubber travels in reverse.
Front Melody Alarm sounds when driving forward
370-744
Side Broom System Cylindrical
370-429 Side Broom System ? 34" / 40" Cylindrical includes (Qty: 2) 17— side brooms. It equips the front of the battery scrubber with dual side brooms, which extends the cleaning path and allow for unique edge cleaning under racking and against walls. Another advantage of the option is that it can be used to clean out expansion joints, and avoid cracks and damage from heavy tires pushing debris deeper into the cracks. Each motor is individually powered by a motor, and the entire system can be pivoted up and turned off when not in use. The side brooms should only be used when traveling on a dry floor and in Forward.
Side Broom System ? 46— Cylindrical
370-430 Side Broom System ? 46— Cylindrical includes (Qty: 2) 19— side brooms. It equips the front of the floor scrubber with dual side brooms, which extends the cleaning path and allow for unique edge cleaning under racking and against walls. Another advantage of the option is that it can be used to clean out expansion joints, and avoid cracks and damage from heavy tires pushing debris deeper into the cracks. Each motor is individually powered by a motor, and the entire system can be pivoted up and turned off when not in use. The side brooms should only be used when traveling on a dry floor and in Forward.
Side Broom Guards
370-435 Side Broom Guards are steel bumpers mounted to the scrubber”s frame, and designed to offer enhanced protection to the side broom if so equipped. The bumpers stick out a few inches on either side, and so will increase the scrubber”s ‘minimum distance to complete a U-Turn—.
Concrete Polishing Package
Concrete Polishing Package is an option that equips our scrubber to also be useful when polishing concrete floors. Depending on the condition of the concrete, customers can use the scrubber to develop a high gloss finish, without wax or any other ‘coatings—. The option includes:
Brass Brush Driver/Idler Upgrade (Cylindrical)
370-507 Brass Brush Driver/Idler Upgrade (Cylindrical) is for applications that require unusually harsh detergents or where a scrubber will encounter corrosive chemicals on the floor. This upgrade replaces the standard aluminum drivers/idlers with brass.
Diffuser/Swing Away Rear Bumper
370-511 Diffuser/Swing Away Rear Bumper was an option developed initially to work with the large stainless steel tank option. The vacuum exhaust is connected to the rear bumper tube and then evenly spread to the floor. Creating a curtain of air just behind the rear squeegee, thus using the available exhaust air to assist drying the floor. Popular with customers with unfinished concrete or other difficult to dry surfaces.
Metal Recovery Lid Upgrade
370-519 Metal Recovery Lid Upgrade replaces the standard ‘smoked— plastic recovery tank visual inspection lid, with a powder painted steel cover. While being more durable, it eliminates the scrubber operators” ability to monitor foam in the recovery tank and potential ingestion by the vacuum motor.
Side Doors ? Cylindrical
Side Doors ? Cylindrical are heavy gage, powder painted steel doors, which hinge open to access the scrub deck. These HD doors mount with a stainless hinge, to the rider scrubber”s steel frame, and protect the scrub deck from collisions into poles, pallets and such. Since the scrub deck sizes vary and often extend outside the scrubber”s frame, they can be exposed to damage. The doors include tall tower rollers, with non-marking polyurethane rollers, which spread impacts better and are less likely to damage or mark drywall.
Side Doors ? Disk
Side Doors ? Disk doors are heavy gage, powder painted steel doors, which hinge open to access the scrub deck. These HD doors mount with a stainless hinge, to the rider scrubber”s steel frame, and protect the scrub deck from collisions into poles, pallets and such. Since the scrub deck sizes vary and often extend outside the scrubber”s frame, they can be exposed to damage. The doors include tall tower rollers, with non-marking polyurethane rollers, which spread impacts better and are less likely to damage or mark drywall.
Stainless Steel Scrub Deck
370-556 Stainless Steel Scrub Deck (Disk Units Only) is 304-grade stainless and best suited for applications where the scrubber is subjected to highly corrosive materials. It replaces the standard powder painted steel deck.
Stainless Steel Tank Baffle
370-560 Stainless Steel Tank Baffle is a 304 grade stainless sheet, and best suited for applications where the recovery tank is subjected to highly corrosive materials. It replaces the standard powder painted steel baffle.
85 Gallon Stainless Steel Tank
370-564 85 Gallon Stainless Steel Tank Upgrade swaps out the standard poly tanks for 304 grade stainless tanks.
Stainless Cylindrical 40" Deck with Hopper
370-572
Squeegee blade material change Linatex to Gum
Squeegee blade material change Linatex to Gum permits the scrubber owner to go with another squeegee blade material other than our standard Linatex, which is known for its exceptional wear. Some applications have rough or grouted floors, so the softer GUM material can offer superior drying as it better seals over the irregularities. For applications with oil, hydraulic fluid, fuels or citrus cleaners, the URETHANE can offer better resistance to the harsh chemicals when often swell the GUM or LINATEX material.
Squeegee blade material change Linatex to Urethane
Squeegee blade material change Linatex to Urethane permits the scrubber owner to go with another squeegee blade material other than our standard Linatex, which is known for its exceptional wear. Some applications have rough or grouted floors, so the softer GUM material can offer superior drying as it better seals over the irregularities. For applications with oil, hydraulic fluid, fuels or citrus cleaners, the URETHANE can offer better resistance to the harsh chemicals when often swell the GUM or LINATEX material.
Urethane Disk Wiper in lieu of Linatex
370-xxx Urethane Disk Wiper in lieu of Linatex. For applications with oil, hydraulic fluid, fuels or citrus cleaners, the URETHANE can offer better resistance to the harsh chemicals when often swell the GUM or LINATEX material
Urethane Cylindrical Wiper in lieu of Linatex
370-949 Urethane Cylindrical Wiper in lieu of Linatex as some applications has rough or grouted floors. For applications with oil, hydraulic fluid, fuels or citrus cleaners, the URETHANE can offer better resistance to the harsh chemicals when often swell the GUM or LINATEX material.
Battery Box, Ind. w/o Battery - Includes Conversion Bracket and Box
370-589
Squeegee Hose with Trap at End
370-600 A longer squeegee hose, to allow a "loop" to be included, which collects water that may drain back out of the hose.
GUM Disk Wiper in lieu of Linatex
370-XXX GUM Disk Wiper in lieu of Linatex as some applications have rough or grouted floors, so the softer GUM material can offer superior drying as it better seals over the irregularities.
GUM Cylindrical Wiper in lieu of Linatex
370-XXX GUM Cylindrical Wiper in lieu of Linatex as some applications have rough or grouted floors, so the softer GUM material can offer superior drying as it better seals over the irregularities.
Bottom Drain Recovery Tank
370-605 Bottom Drain Recovery Tank XR Series allows the scrubber operator to drain the dirty water in the recovery tank from the center of the floor, instead of the standard side drain hose. The perception in some applications is that this center location will drain the dirty water more completely. The downside to this location is that the drain hose is more likely to collect silt and clog before the tank is emptied.
Dual Drain, Bottom and Side Drains
370-606 Dual Drain, Bottom and Side Drains essentially is the additional of a center floor drain in the recovery tank to the standard side mounted drain hose.
CE Package Battery Disconnect No seat lid charge port
370-609
Hopper Screen
370-611 Is a stainless fine mesh, to collect small items that would otherwise fall through the standard size holes in the hopper.
Overhead Guard
Overhead Guard equips the rider with a solid guard, supported by 2 or 4 posts. Ideal for applications with high racking or anywhere there”s a risk of falling objects or debris.
Drain Hose Control
370-622 This is a valve on the recovery drain hose, so the cischarge rate can be adjusted.
Raised Operator Floor Plate
370-626 Raised Operator Floor Plate XR Series brings the foot pedal and foot rest up approximately 3— higher. Developed initially to allow a single scrubber platform to be sold globally, where we encounter a wide range of operator heights.
Seat Belt
370-629 Seat Belt equips the rider scrubber”s standard seat with a simple seat belt.
Seat Belt with Retractable belts and Cut-Off switch
370-632 Seat Belt with Retractable belts and Cut-Off switch equips the rider scrubber with a ‘retracting— set of belts that include a cut off switch for the floor scrubber's key switch circuit. With this option, the battery scrubber will not function until the operator is properly seated, with the latch engaged.
Fill Screen, Solution Tank
370-635
Z-Bart Undercoating
370-644 Z-Bart Undercoating is an excellent option for applications where the scrubber and frame will be exposed to corrosive & damaging chemicals, fumes, spray, dust, etc?. The entire underneath of the scrubber”s powder coated steel main frame are coated in a protective barrier.
Freezer Package, XR
370-646 Include special coating and a small heater to help the machine operate more reliably in coolers and freezers. They work to reduce condensation and also resist any that does form. The electroics also operate better in warmth.
Custom Programming
370-659 Custom Programming gives the company buying the scrubber the ability to more ideally select the parameters and characteristics of the scrubber. Our scrubbers have over 100 parameters programmed into the controller, which control variables like acceleration rate, reverse speed, vacuum timers, low battery lock-outs, etc.
Aluminum Hopper Cylindrical
Aluminum Hopper for Cylindrical decks is a 50% lighter weight part and replaces the standard powder painted steel hopper. The aluminum part is less likely to develop rust over time, but requires more care when empting into steel trash bins as it could dent.
Deleted Cup Holder
370-700
Control Panel Switch Cover
370-702
Rear Upright Hose Protector
370-704 This is an ugly steel frame that protects the items (hoses) on the back in case the machine is backed in into a rack.
Frame Mounted Magnet 36" x 2" x 5" Self cleaning
370-708
Mirror, Dual Front Side Mount
370-740 Mirror, Dual Front Side Mount are material handling style, and mounted to the front sides of the battery scrubber, offering better views for the operator of the floor beside the scrubber.
Mirror, Rear View
370-742 Mirror, Rear View is a material handling style mirror, mounted to the back of the scrubber, offering a better view for the operator when backing up.
Charger, Console 200v/50 Hz AC Japan Only
370-007 Charger, Console 200v/50 Hz AC Japan Only is a charger programmed to work on our WET batteries, but developed to work on a specific AC current (200Volts/ 50Hz).
36v WET (6) 6v / 420ah & 220v 36v Charger
370-083
Export Crating, Stud Frame w/ Cardboard Outer Covering
370-100 Export Crating includes a number of extra steps for transit across oceans. Some of these steps are based on shipping requirements (like treated lumber in the pallet), and others are our own steps to reduce salt corrosion, etc. The packaging includes special sheets that the battery scrubber is parked on top of, and then shrinks wrapping to seal from the environment. Special dry packs to absorb moisture are installed in the central command (electrical) boxes and under the floor scrubber.
Battery Disconnect
370-354 Battery Disconnect gives the scrubber operator the ability to disconnect the battery pack leads between the batteries and the controller. Then an external charger can be plugged in for recharging the batteries. It also comes in handy for servicing the battery scrubber, as disconnecting the batteries is recommended before conducting any auto-scrubber repairs.
Charge Inhibit Switch
370-355 Charge Inhibit Switch automatically disables the traction system on the scrubber, anytime the recharge plug is engaged. Intended to keep operators from attempting to drive the floor scrubber away with the charger still plugged in.
CE Sticker
370-608 CE Sticker indicates that this scrubber complies with the standards and requirements of the CE.
Export Crating
370-99 Export Crating includes a number of extra steps for transit across oceans. Some of these steps are based on shipping requirements (like treated lumber in the pallet), and others are our own steps to reduce salt corrosion, etc. The packaging includes special sheets that the battery scrubber is parked on top of, and then shrinks wrapping to seal from the environment. Special dry packs to absorb moisture are installed in the central command (electrical) boxes and under the floor scrubber.
Delete Charger Cycle Meter
370-280
Delete the Standard (Qty 6) 6-volt / 325ah Batteries
370-810 Delete the Standard (Qty 6) 6-volt / 325ah Batteries allows the customer to get a credit back for buying the scrubber without any batteries. The delete credit is less $$ than it will cost to supply batteries locally, and for domestic shipments we prefer to have OEM batteries used. There is a wide variety of battery sizes, terminal posts, and not the least of which? quality. We use the highest quality batteries available. Another reason for the small credit is that all scrubbers are tested for 15 minutes, so the delete option requires extra steps after QC to remove the batteries.
Delete Charger (36v/36amp)
370-820 Delete Charger (36v/36amp) allows the customer to get a credit back for buying the scrubber without a charger. The delete credit is less $$ than it will cost to source a charger locally, and for domestic shipments we prefer to have OEM charger used. There is a wide variety of AC/DC specifications, capacities, and not the least of which? quality. We use the highest quality chargers available, as they reduce our warranty risk on the batteries.
