Click on the pictures to see a larger picture and more pictures if available.
Battery & Charger Upgrade Options ? Lead Acid (WET)
Instead of the standard 245ah batteries (WET), a set (Qty: 6) 6-volt WET batteries and an upgraded charger is provided. These batteries offer approximately 35% more run time than the standard 245ah batteries.
Battery & Charger Upgrade Options ? Maintenance Free (AGM)
250-020 Instead of the standard 245ah batteries (WET), a set (Qty: 6) 6-volt / 325ah AGM (Maintenance Free) batteries and special charger is provided. Our experience has been that AGM batteries may not offer as many cycles (recharges) as properly maintained lead acid (WET) batteries. They are suitable for customers who prefer their maintenance free nature, and reduced gassing during recharge.
Charger Console, 36v/40amp ? 220v AC
250-060 Charger Console, 36v/40amp ? 220v AC, Lester is designed to work on specific and unique AC currents.
Charger Console, Dual Pro Universal
250-081 Charger Console, Dual Pro Universal Voltage WET (36v/25amp) is a charger programmed to work on our WET batteries, which can uniquely work on any markets AC current (Volts or Hz). Frequently supplied on machines going overseas.
Charger On-Board SPE Sealed 36v/20amp AGM
250-104 Charger On-Board SPE Sealed 36v/20amp is designed to mount directly to the auto scrubber and eliminate the need to store a charger remotely. This unit has some protection against water, and its DC output is 24-volt/20amp.
On Board Charger 36v 25a Quick Charge, WET
250-106
Plastic Battery Cover
250-036 Plastic Battery Cover is a simple sheet of plastic that covers the tops of the batteries, offering a 2nd layer of protection for the battery posts. This walk behind scrubber comes standard with individual rubber booties for each battery post, but some customers prefer a supplemental sheet that covers the entire battery, cell caps and all.
Single Point Water System for (Qty 6) 6v/245ah batteries
250-038 Single Point Water System for (Qty 6) 6v/245ah batteries allows easy battery watering, by connecting all of the battery cells via special caps. These caps connect to a single tube for watering of the scrubber”s batteries, and help to equalize the electrolyte levels.
Chemical Free, Oscillating, Strip/Scrub Disk System
250-141 Chemical Free, Oscillating, Strip/Scrub Disk System uses the oscillation of the brush driver, special sanding pads, enhanced scrub motor hp, rpm and pressure to allow the floor scrubber to clean floors or strip wax without using harsh chemicals. The option includes a ‘mode— switch allowing the operator to switch back to traditional settings, making it uniquely able to move from strip mode, back to scrub mode.
ECON- Energy Saver Switch
250-290 ECON- Energy Saver Switch allows the scrubber operator to choose between standard performance range (maximum) or ‘reduced— performance range and thus conserve energy and extend the runtime. Intended to be one of many environmentally conservative measures we”re taking to reduce energy use.
Spray Jet option
250-127 Spray Jet option equips the scrubber with a heavy duty hose 4” - 10” and spray nozzle. This allows the operator to use the scrubber”s clean solution under pressure (3.0 gpm / 45 psi) to flush out the recovery tank when draining the tank when fresh water source is not within reach. Operator can also cleanout the scrub deck/hopper, pre-spray a large floor area for better detergent dwell time, cleaning under racks, around equipment, into restrooms and more.
Vacuum Wand
250-129 Vacuum Wand extends the reach of the scrubber”s vacuum system. The option includes a steel wand and vacuum shoe, and a 12” flexible hose to connect to the recovery tank. It permits the operator to recover spills under racking, behind cabinets or cleaning restroom floors.
Spray Jet / Vac Wand Combo
250-131 Spray Jet / Vac Wand Combo equip the scrubber with both of the previously described options.
On-Board Soap System (SUDS)
250-138 On-Board Soap System (SUDS). This Super-concentrated Universal Dispensing System automatically and precisely meters the soap into the solution stream, thus avoiding spills, misuse of chemicals, unauthorized dilution adjustments, etc. By blending the scrubber soap at the end of the solution stream, only fresh water is used to fill the tank, or run through the solution system”s filter and solenoid valve, reducing potential clogs with these items. The SUDS jugs include cap inserts with valves to protect operators from exposure, a big safety feature of traditional drums and pales of soap. The system allows the operator to run with it OFF, Normal or Double Dose. The option includes a case of (6) ½ gallon jugs of PowerCat detergent to get the customer started.
Tires ? Grey Non-marking Front and Rear
250-189 Tires ? Grey Non-marking tires are in place of the standard black rubber tires. This allows customers to operate on sensitive floors like ceramic tile, glossy epoxy or waxed surfaces with lower risks of potential black marks. WARNING: Grey tires are more susceptible to harsh industrial chemicals, and so are only recommended for use in "commercial" applications. Therefore, they come with a limited warranty.
Front Tire, Polyurethane in lieu of black hytraq rubber
250-181
Front Tire, Grey Non Marking in lieu of black hytraq rubber
250-183
Front Tire, P-7 in lieu of black hytraq rubber
250-186
Vacuum Muffler Package
250-225 Vacuum Muffler Package GTX Series equips the floor scrubber with enhanced sound reduction material and vacuum exhaust routing. The option is popular in applications where every measure of sound reduction is appreciated, like hospitals, casinos or anywhere that minimal decibel readings are required.
Managers” Lock-Out Brush Pressure
250-305 Managers” Lock-Out Brush Pressure allows a Manager, with a private key, to lock out the battery floor scrubber”s Scrub pressure adjustment. Our scrubbers offer 5 down pressure settings, and should only be used on maximum settings for floors with heavy soil build up or stripping floor finish. To avoid unnecessary wear on brushes or brushes, this lockout can be employed to maintain Managements” preferred settings.
Manager”s Lock-Out Solution Control
250-310 Manager”s Lock-Out Solution Control permits a Manager, with a private key, to lock out the scrubber”s Solution Flow adjustment. Our floor scrubbers offer 6 settings for solution flow (Off, 0.2 gpm, 0.4 gpm, 0.6 gpm, 0.8 gpm, 1.0 gpm), with Heavy flow only needed for thick soil, dusty applications or times when cleaning at a higher transport speed. To limit the waste of water, the solution setting can be locked.
E-STOP
250-285 E-STOP is a RED kill switch on the dash board, that when depressed cuts off the key switch circuit, disabling all systems on the scrubber. It is intended for use during a panic, when the operator may struggle to locate or operate the key switch.
LED Headlight Upgrade
250-300 LED Headlight Upgrade is a swap out option equipping the scrubber with LED headlight, in place of the standard ones. These LED units offer reduced energy consumption and are significantly brighter. Especially helpful in ‘low light— applications like remote areas of a warehouse or operating in semi trailers, freezers, etc...
Rental Package Central Command
250-330 This is a central command built with old fashioned (1990's) technology. A simple Curtis peed controller and all other systems running on switches, relays and circuit breakers. It's designed for use in markets that prefer reliability and ease of service over all of the automation we have with our standard system.
Seat with Switch
250-335 Seat with Switch equips the standard seat with a ‘cut-off— switch. This switch disables the key switch circuit on the scrubber if the operator is not properly seated.
Strobe Light
250-340 Strobe Light ? Amber is a flashing light mounted to the top/rear of the scrubber”s recovery tank. The strobe light increases the floor scrubber”s visibility to other vehicles or people, and is recommended in congested facilities.
)window.location='http://www.tomcatequip.com/scrubber/optionspics/gtx/frontsolutionshutoff2.jpg')
Dash Mount Solution Shut-Off
250-352 Dash Mount Solution Shut-Off gives the scrubber operator the ability to shut off the solution flow with a single switch, instead of cycling down with the toggle +/-. It includes a 2nd valve on the scrub deck and so also reduces the potential for water leakage during storage.
Turn, Brake, Back Up Light Kit Front & Rear-LED with Stalk
250-358
Side Broom System
250-427 Side Broom System ? Recommended on 24— & 27— Cylindrical only. It equips the front of the battery scrubber with dual side brooms, which extends the cleaning path and allow for unique edge cleaning under racking and against walls. Another advantage of the option is that it can be used to clean out expansion joints, and avoid cracks and damage from heavy tires pushing debris deeper into the cracks. Each motor is individually powered by a motor, and the entire system can be pivoted up and turned off when not in use. The side brooms should only be used when traveling on a dry floor and in Forward.
Water for Side Broom System
250-433 Water for Side Broom System ? is a unique option which supplies a small and continuous stream of solution from the clean tank, to each of the side brooms. This reduces any dust that the side brooms could kick up, and can help extend the cleaning of the detergent. Since the system is beyond the scrubber”s side wipers, water control on turns is reduced. The system comes with a switch, so in preparation for a turn, the operator can shut off the water and maintain good water control.
Concrete Polishing Package
Concrete Polishing Package is an option that equips our scrubber to also be useful when polishing concrete floors. Depending on the condition of the concrete, customers can use the scrubber to develop a high gloss finish, without wax or any other ‘coatings—. The option includes:
Side Broom Guards
250-435 Side Broom Guards are steel bumpers mounted to the scrubber”s frame, and designed to offer enhanced protection to the side broom if so equipped. The bumpers stick out a few inches on either side, and so will increase the scrubber”s ‘minimum distance to complete a U-Turn—.
Brass Brush Driver/Idler Upgrade (Cylindrical)
250-507 Brass Brush Driver/Idler Upgrade (Cylindrical) is for applications that require unusually harsh detergents or where a auto scrubber will encounter corrosive chemicals on the floor. This upgrade replaces the standard aluminum drivers/idlers with brass.
Metal Recovery Lid Upgrade
250-519 Metal Recovery Lid Upgrade replaces the standard ‘smoked— plastic recovery tank visual inspection lid, with a powder painted steel cover. While being more durable, it eliminates the scrubber operators” ability to monitor foam in the recovery tank and potential ingestion by the vacuum motor.
Upgraded Scrub Motors (Disk Only)
250-523 Upgraded Scrub Motors (Disk Only) ? Includes 1.0/high rpm motors and increases the scrubbers” already high scrubbing power. Some applications benefit from an increase in scrubbing power, rpm, down pressure or all of the above. These motors can generate and sustain 35% more power, allowing heavy soil, tire marks or stripping to be completed in less time.
12" Heavy Duty FWD Upgrade
250-525
Side Doors ? Disk
Side Doors ? Disk are heavy gage, powder painted steel doors, which hinge open to access the scrub deck. These HD doors mount with a stainless hinge, to the rider scrubber”s steel frame, and protect the scrub deck from collisions into poles, pallets and such. Since the scrub deck sizes vary and often extend outside the scrubber”s frame, they can be exposed to damage. The doors include tall tower rollers, with non-marking polyurethane rollers, which spread impacts better and are less likely to damage or mark drywall.
Side Doors ? Cylindrical
Side Doors ? Cylindrical are heavy gage, powder painted steel doors, which hinge open to access the scrub deck. These HD doors mount with a stainless hinge, to the rider scrubber”s steel frame, and protect the scrub deck from collisions into poles, pallets and such. Since the scrub deck sizes vary and often extend outside the scrubber”s frame, they can be exposed to damage. The doors include tall tower rollers, with non-marking polyurethane rollers, which spread impacts better and are less likely to damage or mark drywall.
Stainless Steel Scrub Deck
Stainless Steel Scrub Deck (Disk Units Only) is 304-grade stainless and best suited for applications where the scrubber is subjected to highly corrosive materials. It replaces the standard powder painted steel deck.
Stainless Steel Tank Baffle
250-560 Stainless Steel Tank Baffle is a 304 grade stainless sheet, and best suited for applications where the recovery tank is subjected to highly corrosive materials. It replaces the standard powder painted steel baffle.
Different length squeegee in lieu of standard size (linatex)
Different length squeegee in lieu of standard size (linatex) allows the scrubber owner to go with a different squeegee than what is standard. While our standard squeegee size is designed to balance water control on turns and maneuverability through congested areas, some accounts prefer a substitute size to better meet their needs.
Squeegee blade material change Linatex to Gum
Squeegee blade material change Linatex to Gum permits the scrubber owner to go with another squeegee blade material other than our standard Linatex, which is known for its exceptional wear. Some applications have rough or grouted floors, so the softer GUM material can offer superior drying as it better seals over the irregularities. For applications with oil, hydraulic fluid, fuels or citrus cleaners, the URETHANE can offer better resistance to the harsh chemicals when often swell the GUM or LINATEX material.
Squeegee blade material change Linatex to Urethane
Squeegee blade material change Linatex to Urethane permits the scrubber owner to go with another squeegee blade material other than our standard Linatex, which is known for its exceptional wear. Some applications have rough or grouted floors, so the softer GUM material can offer superior drying as it better seals over the irregularities. For applications with oil, hydraulic fluid, fuels or citrus cleaners, the URETHANE can offer better resistance to the harsh chemicals when often swell the GUM or LINATEX material.
Urethane Disk Wiper in lieu of Linatex
250-948 Urethane Disk Wiper in lieu of Linatex. For applications with oil, hydraulic fluid, fuels or citrus cleaners, the URETHANE can offer better resistance to the harsh chemicals when often swell the GUM or LINATEX material
Urethane Cylindrical Wiper in lieu of Linatex
250-948 Urethane Cylindrical Wiper in lieu of Linatex. For applications with oil, hydraulic fluid, fuels or citrus cleaners, the URETHANE can offer better resistance to the harsh chemicals when often swell the GUM or LINATEX material.
GUM Disk Wiper in lieu of Linatex
250-XXX GUM Disk Wiper in lieu of Linatex as some applications have rough or grouted floors, so the softer GUM material can offer superior drying as it better seals over the irregularities.
GUM Cylindrical Wiper in lieu of Linatex
250-XXX GUM Cylindrical Wiper in lieu of Linatex as some applications have rough or grouted floors, so the softer GUM material can offer superior drying as it better seals over the irregularities.
Quick Fill Hose Option
250-220
Aluminum Scrub Deck
15' Tank Drain Hose
250-599
Squeegee Hose with Trap at End
250-600 Squeegee Hose with Trap at End is an option for customers especially concerned with any drip back from the squeegee hose. The scrubber is standard with a vacuum delay, which generally dries out the length of the squeegee hose. This ‘trap— simply entails an additional length of hose, which is wrapped into a loop, thus creating a small trap for residual dirty water to collect.
Dual Drain, Bottom and Side Drain
250-606
CE Package, Battery Disconnect includes E-stop
250-609
Seat Belt
250-629 Seat Belt equips the rider scrubber”s standard seat with a simple seat belt.
Seat Belt with Retractable belts and Cut-Off switch
250-632 Seat Belt with Retractable belts and Cut-Off switch equips the rider scrubber with a ‘retracting— set of belts that include a cut off switch for the floor scrubbers key switch circuit. With this option, the scrubber will not function until the operator is properly seated, with the latch engaged.
Z-Bart Undercoating
250-644 Z-Bart Undercoating is an excellent option for applications where the scrubber and frame will be exposed to corrosive & damaging chemicals, fumes, spray, dust, etc?. The entire underneath of the scrubber”s powder coated steel main frame are coated in a protective barrier.
Dual Vacuum Motors, 36v
250-645
Freezer Package, GTX
250-646 Includes special coating and a small heater to help the machine operate more reliably in coolers and freezers. They work to reduce condensation and also resist any that does form. The electronics also operate better in warmth.
Plate, Upturned Squeegee
250-647
Custom Programming
250-659 Custom Programming gives the company buying the scrubber the ability to more ideally select the parameters and characteristics of the auto floor scrubber. Our scrubbers have over 100 parameters programmed into the controller, which control variables like acceleration rate, reverse speed, vacuum timers, low battery lock-outs, etc.
Aluminum Hopper for Cylindrical
Aluminum Hopper for Cylindrical is a 50% lighter weight part and replaces the standard powder painted steel hopper. The aluminum part is less likely to develop rust over time, but requires more care when empting into steel trash bins as it could dent.
Charger, Console 200v/50 Hz AC Japan
250-007 Charger, Console 200v/50 Hz AC Japan Only is a charger programmed to work on our WET batteries, but developed to work on a specific AC current (200Volts/ 50Hz).
Battery Upgrade (4) 6v/325ah with (220v Charger)
250-023 Battery Upgrade (4) 6v/325ah with (220v Charger) supplies the standard scrubber and batteries with a special AC charger for certain foreign markets.
Export Crating Stud Frame w/ Cardboard Outer Covering
250-100 Export Crating includes a number of extra steps for transit across oceans. Some of these steps are based on shipping requirements (like treated lumber in the pallet), and others are our own steps to reduce salt corrosion, etc. The packaging includes special sheets that the auto floor scrubber is parked on top of, and then shrinks wrapping to seal from the environment. Special dry packs to absorb moisture are installed in the central command (electrical) boxes and under the scrubber.
Manual Vac Toggle Switch-white
250-312
Battery Disconnect
250-354 Battery Disconnect gives the scrubber operator the ability to disconnect the battery pack leads between the batteries and the controller. Then an external charger can be plugged in for recharging the batteries. It also comes in handy for servicing the floor scrubber, as disconnecting the batteries is recommended before conducting any scrubber repairs.
Charge Inhibit Switch
250-355 Charge Inhibit Switch automatically disables the traction system on the battery scrubber, anytime the recharge plug is engaged. Intended to keep operators from attempting to drive the scrubber away with the charger still plugged in.
CE Sticker
250-608 CE Sticker indicates that this battery floor scrubber complies with the standards and requirements of the CE.
Raised Operator Floor Plate
250-626 Raised Operator Floor Plate GTX Series brings the foot pedal and foot rest up approximately 3— higher. Developed initially to allow a single scrubber platform to be sold globally, where we encounter a wide range of operator heights.
Front Solution Site Gauge
250-648 Front Solution Site Gauge-GTX gives the rider scrubber operator a visual indication of the remaining solution level in the clean water tank. The standard gauge is a combination drain hose, at the rear of the scrubber, in good view when refilling the tank. The front sight tube option includes a small blue float ball to make the height of the solution more visible. The tank design on the rider allows accommodates the tube in the bottom ½ of the tank, which is the most critical section to monitor.
Crushable Drain Hose GTX Series
250-660
Export Crating
250-99 Export Crating includes a number of extra steps for transit across oceans. Some of these steps are based on shipping requirements (like treated lumber in the pallet), and others are our own steps to reduce salt corrosion, etc. The packaging includes special sheets that the auto floor scrubber is parked on top of, and then shrinks wrapping to seal from the environment. Special dry packs to absorb moisture are installed in the central command (electrical) boxes and under the scrubber.
Delete the Standard (Qty 6) 6-volt / 245ah Batteries
250-810 Delete the Standard (Qty 6) 6-volt / 245ah Batteries allows the customer to get a credit back for buying the scrubber without any batteries. The delete credit is less $$ than it will cost to supply batteries locally, and for domestic shipments we prefer to have OEM batteries used. There is a wide variety of battery sizes, terminal posts, and not the least of which? quality. We use the highest quality batteries available. Another reason for the small credit is that all scrubbers are tested for 15 minutes, so the delete option requires extra steps after QC to remove the batteries.
Delete Charger (36v/25amp)
250-820 Delete Charger (36v/25amp) allows the customer to get a credit back for buying the scrubber without a charger. The delete credit is less $$ than it will cost to source a charger locally, and for domestic shipments we prefer to have OEM charger used. There is a wide variety of AC/DC specifications, capacities, and not the least of which? quality. We use the highest quality chargers available, as they reduce our warranty risk on the batteries.
